Jandy Levolor K-2300:
The Levolor K-2300 includes 2 sensors with wire, controller and 2 solenoid valves. The system contains non-corrosive components, NEMA 4 enclosure, all suitable for use in a pool and mechanical room environment. The system provides control and adjustability for two separate environments, ease of operation and service accessibility.

Specifications:

Dimensions
Enclosure:	10” x 5” x 4.5” with mounting screws
Sensor:	2 Sensors (Skimmer Sensor and Static Pipe Sensor), 2 Probes, Wire 50ft-200ft in 50ft increments
Valve:	2 – 1” 24VAC Solenoid
Sensor Housing:	2 – 5.5” in diameter

• The Pool water level is controlled automatically with +/- 1/8” (12mm) of normal water level.
• Water level control system includes tow separate fill sensors, which install at the nominal water level, a control panel mounted in the equipment area, two separate solenoid valves in-line with make-up water to each environment.
• Sensor Static pipe should be installed according to the drawings, with 2” PVC with no reductions.
• Fill Sensors should be mounted at water level, inside the static pipe located according to the drawings.
• Units with floats or moving parts will not be considered as equal and shall be rejected.
• Sensor should be connected to the control panel with a maximum of 200 ft of wire provided as part of the system. Sensor wire comes in 50 ft increments with a maximum of 200 ft.
• Control panel displays indicating Power, Sensor I active, Filling I active, Sensor II active and Filling II active.
• System has adjustable feed alarms suitable for the application as determined by the drawings.
• System has a time delay between sensing and filling before initializing the Solenoid Valves.
• System is shipped with 220VAC 50/60Hz, field adjusted for 110VAC and is hard wired into a panel for permanent installation.
• Solenoid valves offered in brass or fiberglass and sized according to the drawings and normally closed, 24VAC and 0.6amps at a peak, as supplied with the level control system.

Keep Everything "On The Level"
The Jandy Levolor water leveling systems electronically maintain water levels in pools, spas, fountains and ponds. The Levolor System can be used anywhere a constant level of water is needed to maintain a beautiful appearance and protect equipment. Easy to install on new or existing pools and spas, the Levolor System does not require structural modifications for installation. The solid state electronic controls have no moving parts to wear out or rust.

Product Features:
• Waterproof enclosure
• Solid state sensor and valve
• No in deck canisters or under deck pressurized fill lines
• No moving parts
• Perfect for vanishing edge pools
• Lockout feature guarentees not to over fill or hide leaks

Jandy’s Levolor water leveling technology allows more time to enjoy your pool and spa while providing a higher level assurance that your equipment is protected and your water level is always correct. Gone are the days of manually filling your pool or spa with the garden hose.

Completely Electronic - No moving parts:
Modern pool and spa designs require modern electronics to maintain hydraulic integrity, protect equipment, and to simply keep your beautiful aquascape flowing as it was designed. Unfortunately, evaporation and splashing are a natural part of the pool and spa environment. Levolor addresses the concern of lost water with an elegant solution - a completely electronic system with no moving parts to wear out or rust. With the unique time out feature, Levolor is guaranteed to never overfill.
 

Easy Installation:
Installation is quick and easy and can be performed with no modifications to the pool surface or structure since Levolor needs no extra in-deck canisters or under-deck pressurized lines. The sensors can be located in either a skimmer throat, behind the weir door arc or a< static pipe - wherever a constant level of water can be measured. For convenience, sensor wires include both skimmer and static pipe sensors. Electronics are contained in a waterproof, wall mounted unit built for an outdoor environment. Everything is easily wired through 1/2” conduit connections. The easy-to-read LED display effectively communicates the status, if you ever need to check the system at all.

A Model For Any Application:
With models for pool, spa, dual equipment, fountains and Vanishing Edge catch basins, we have an ideal water leveling solution for your unique design. Most designs will benefit from our basic fill models, such as the K-1100 or LX2. For two separate bodies of water, the K-2300 provides everything you need, and the K-2000 is ideal for Vanishing Edge, perimeter overflow designs where high and low level sensing is needed, and activates a pump. The K-2100 is for ponds with a low level cut-off that turns off a pump or light.